Viscosity & Flash Point Standards

Certified Viscosity Check Oils.png

CANNON certified viscosity check oils verify SAE target viscosities for kinematic viscometers, cold-cranking simulators and mini-rotary viscometers per ASTM D445, D5293 and D4684 respectively. Each check oil contains a commercial engine oil with certified values at common blend target values for density in g/cm³ (g/mL) at 15 °C, kinematic viscosity in mm²/s (cSt) at 40 °C and 100 °C as well as cranking and pumping viscosities in mPa∙s (cP) at SAE J300 specification temperatures. CANNON certified viscosity check oils are available in 1 L (quart) and 3.8 L (gallon) sizes.

ASTM D445, ASTM D5293, ASTM D4684

Certified Viscosity Check Oils

Flash Point Reference Materials.jpg

CANNON flash point reference materials are produced in accordance with ASTM D56, Tag Closed Cup Flash Point, ASTM D92, Cleveland Open Cup Flash Point and ASTM D93, Pensky Marten Closed Cup Flash Point. Lot specific data including average flash point and observed standard deviation from a statistical analyis of 40 tests in 20 different laboratories is provided with each standard. Flash Point Reference Materials are sold in 200 mL bottles.

ASTM D56, ASTM D92, ASTM D93

Flash Point Reference Materials

Flow cup viscosity standards.png

CANNON flow cup viscosity standards are for use in Zahn, Shell and Ford flow cups. Lot specific kinematic viscosity data in mm²/s (cSt) and calculated cup drain times are provided with each standard. Nominal values at 25 °C are shown in the associated table. Data is also provided at 20 °C and 23 °C.

ASTM D4212, ASTM D1200

Flow Cup Viscosity Standards

General purpose viscosity standards.jpg

All CANNON general purpose viscosity standards meet the precision specifications of ASTM D445/446 and ISO 3104/3105. Lot specific data is provided with each standard.

ASTM D445, ASTM D446, ISO 3104, ISO 3105

General Purpose Viscosity Standards

HTHS viscosity standards.jpg

CANNON high temperature viscosity standards are produced in accordance with ASTM D5481, Apparent Viscosity at High-Temperature and High-Shear Rate by Multicell Capillary Viscometer and ASTM D4741, Viscosity at High Temperature and High Shear Rate by Tapered Plug Viscometer. ASTM D6616 TBS tet at 100 °C applies to certain standards as well. Lot specific viscosity data in mPa·s (cP) is provided with each standard.

ASTM D4683, D4741, D5481, D6616

High Temperature (HTHS) Viscosity Standards

High Viscoaisy Standards.jpg

CANNON high viscosity standards cover viscosity ranges of particular interest for asphalt and polymer viscosity determinations. See ASTM D2170, Kinematic Viscosity of Asphalts (Bitumens) and D2171, Viscosity of Asphalts by Vacuum Capillary Viscometer. Lot specific kinematic viscosity data in mm²/s (cSt) and dynamic viscosity data in mPa·s (cP) is provided with each standard as appropriate.

ASTM D2170, ASTM D2171

High Viscosity Standards

Low Temp Viscosity standards.jpg

CANNON low temperature viscosity standards verify viscometer performance at sub-zero temperatures. These standards are applicable to SAE Specification J300 as well as a variety of ASTM methods including ASTM D2983, Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer, ASTM D3829, Predicting the Borderline Pumping Temperature of Engine Oil, ASTM D4684, Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature, ASTM D6821, Low Temperature Viscosity of Drive Line Lubricants in a Constant Shear Stress Viscometer, ASTM D6896, Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature and ASTM D5293, Apparent Viscosity of Engine Oils and Base Stocks Between –5 °C and –35 °C Using Cold-Cranking Simulator.

ASTM D2983, ASTM 3829, ASTM 4684, ASTM 5293, ASTM D6821, ASTM D6896, SAE J300

Low Temperature Viscosity Standards (General, CCS and CMRV)

Silicone viscosity standards.jpg

CANNON silicone viscosity standards are intended for use with rotational viscometers only. Silicone viscosity standards are not recommended for glass capillary viscometers (including vacuum viscometers), metal cup-type viscometers (such as ISO, Zahn, Ford and Shell cups), or any other viscometers providing kinematic viscosity—CANNON hydrocardon-based oil standards should be used for these types of viscometers.

 

CANNON silicone viscosity standards are specifically formulated for use with rotational viscometers. Lot specific viscosity data in mPa·s (cP) at 20 °C, 23 °C, 24 °C, 25 °C, 26 °C, 27 °C and 40 °C is provided with each standard. Viscosity standards are sold in 500 mL bottles.

.

Silicone Viscosity Standards for Rotational Viscometers

SimpleVis viscosity standards.jpg

CANNON SimpleVis viscosity standards verify the performance of the CANNON SimpleVIS automated viscometer. Lot specific kinematic viscosity data is provided at 20 °C, 25 °C, 40 °C, and 100 °C.

.

SimpleVIS® Viscosity Standards

Thomas Stromer viscosity standards.jpg

Thomas-Stormer viscosity standards calibrate manual and electronic Thomas-Stormer viscometers. The KREBS UNIT (KU) is often used for Thomas-Stormer viscometers. Lot specific viscosity data (in cP and KU) is provided with each standard at 23 °C, 24 °C, 24.5 °C, 25 °C, 25.5 °C and 26 °C.

.

Thomas®-Stormer® Viscosity Standards

התקשר אלינו

T: +972-4-9989971  

F: +972-4-9989952

כתוב לנו

levenson@levensonag.com

© 2019 by Levenson Agencies Ltd.

 Created with Wix.com